BWHCH - MIL-C-22750E, 17875 WHITE EPOXY, F-09 P328
- MSDS: BWHCH
- Manufacturer: SEAGRAVE COATINGS CORP OF VA
- Product Name: MIL-C-22750E, 17875 WHITE EPOXY, F-09 P328
- National Stock Number: 8010-01-350-4734
Product Identification
Product ID:MIL-C-22750E, 17875 WHITE EPOXY, F-09 P328
MSDS Date:07/27/1993
FSC:8010
NIIN:01-350-4734
Kit Part:Y
MSDS Number: BWHCH
Responsible Party
PORTSMOUTH, VA 23701
US
Emergency Phone: 804-488-4411/800-424-9300 CHERMTREC
Info Phone: 804-488-4411
Cage: 60163
Contractor
Telephone: 757-397-2223
Cage: 60163
Ingredients
TITANIUM DIOXIDE (VAPOR PRESSURE 0.0 MM HG @ 20C)
CAS: 13463-67-7
RTECS: XR2275000
Fraction By Weight: 35%
ACGIH TLV: 10 MG/M3
SILICON DIOXIDE (VAPOR PRESSURE 10.0 MM HG @ 20C)
CAS: 14808-60-7
RTECS: VV7330000
Fraction By Weight: 15%
ACGIH TLV: 0.1 MG/M3;STEL 0.1
AROMATIC HYDROCARBON 150 (VAPOR PRESSURE 3.0 MM HG @ 20C)
CAS: 64742-94-5
RTECS: SE7546500
Fraction By Weight: 5%
ACGIH TLV: 100 PPM
METHYL ETHYL KETONE (SARA 313) (VAPOR PRESSURE 83.0 MM HG @
CAS: 78-93-3
RTECS: EL6475000
Fraction By Weight: 20%
ACGIH TLV: 200 PPM;STEL 300 PPM
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
EPOXY RESIN (VAPOR PRESSURE 0.0 MM HG @ 20C)
CAS: 25068-38-6
RTECS: KC2100000
Fraction By Weight: 35%
2.469 LBS/GAL
RTECS: 9999999VO
Hazards
Routes of Entry: Inhalation:YES Skin:UNKNOWN Ingestion:YES
Health Hazards Acute and Chronic:INHALATION: IRRITATION TO RESPIRATORY
TRACT, HEADACHE, DIZZINESS, NAUSEA. SKIN CONTACT: PRIMARY
IRRITATION. EYE CONTACT: PRIMARY IRRITATION.
Explanation of Carcinogenicity:SILICON DIOXIDE KNOWN OR SUSPECTED
CARCINOGEN.
Medical Cond Aggravated by Exposure:PRE-EXISTING SENSITIVITY TO
SOLVENTS CAN CAUSE A HEIGHTENED REACTION TO EXPOSURE TO THIS
PRODUCT.
First Aid
First Aid:INHALATION: REMOVE TO FRESH AIR, RESTORE BREATHING. CONSULT A
PHYSICIAN. SKIN CONTACT: FLUSH WITH WATER. EYE CONTACT: FLUSH
IMMEDIATELY WITH LARGE AMOUNTS OF WATER. CONSULT A PHYSICIAN.
Fire Fighting
Flash Point Method:TCC
Flash Point:25.0F,-3.9C
Lower Limits:0.8
Upper Limits:7.0
Extinguishing Media:FOAM, WATER FOG, DRY CHEMICAL
Fire Fighting Procedures:WATER MAY BE USED TO COOL CLOSED CONTAINERS TO
PREVENT PRESSURE BUILD-UP AND POSSIBLE AUTOIGNITION OR EXPLOSION
WHEN EXPOSED TO EXTREME HEAT.
Unusual Fire/Explosion Hazard:KEEP CONTAIERS TIGHTLY CLOSED. ISOLATE
FROM HEAT, SPARKS, AND OPEN FLAME. CLOSED CONTAINERS MAY EXPLODE
WHEN EXPOSED TO EXTREME HEAT.
Accidental Release
Spill Release Procedures:AVOID BREATHING SOLVENT VAPOR. ENSURE ADEQUATE
VENTILATION. AVOID SPARKS, FLAMES, AND ANYTHING WHICH COULD CAUSE
FIRE.
Handling
Handling and Storage Precautions:STORE IN A COOL DRY AREA WITH
VENTILATION SUITABLE FOR STORING MATERIALS SHOWN IN THE INGREDIENT
SECTION.
Other Precautions:PROVIDE RESPIRATORY PROTECTION AGAINST FUMES
GENERATED DURING BURNING.
Exposure Controls
Respiratory Protection:NIOSH/OSHA APPROVED RESPIRATOR TYPES SUITABLE
FOR MATERIALS IN INGREDIENT SECTION RECOMMENDED. APPROVED
CHEMICAL/MECHANICAL FILTERS RECOMMENDED WHEN VENTILATION
RESTRICTED. APPROVED AIRLINE TYPE RESPI RATOR/HOODS RECOMMENDED IN
CONFINED AREA
Ventilation:SUFFICIENT VENTILATION IN VOLUME & PATTERN SHOULD BE
PROVIDED TO KEEP AIR CONTAMINATION BELOW CURRENT TLV/PEL.
Protective Gloves:RECOMMENDED FOR PROLONGD/REPEATD CONTACT
Eye Protection:CHEMICAL GOGGLES W/SDSHIELDS/FACE SHIELD
Other Protective Equipment:USE PROTECTIVE CREAMS WHERE SKIN CONTACT IS
LIKELY. REMOVE AND WASH CONTAMINATED CLOTHING BEFORE REUSE.
Work Hygienic Practices:WASH HANDS BEFORE EATING OR SMOKING. SMOKE IN
DESIGNATED AREA ONLY.
Supplemental Safety and Health
Chemical Properties
HCC:F2
Boiling Pt:B.P. Text:175 TO 410F
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:INSOLUBLE
Appearance and Odor:WHITE LIQUID, ODOR OF KETONE SOLVENTS
Percent Volatiles by Volume:37.3
Stability
Stability Indicator/Materials to Avoid:YES
OXIDIZING MATERIALS CAN CAUSE A VIGOROUS REACTION.
Hazardous Decomposition Products:AS WITH ANY OTHER ORGANIC MATERIAL,
COMBUSTION WILL PRODUCE CARBON DIOXIDE AND PROBABLY CARBON
MONOXIDE.
Disposal
Waste Disposal Methods:SOAK LIQUIDS WITH SAWDUST OR RAGS AND REMOVE.
FLUSH WITH WATER IF POSSIBLE. AVOID SKIN CONTACT. DISPOSAL SHOULD
BE IN ACCORDANCE WITH LOCAL, STATE, AND FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.